PLUMBING BASICS: THE FIRST STEP FOR BATHTUB INSTALLATION

Plumbing Basics: The First Step for Bathtub Installation

Plumbing Basics: The First Step for Bathtub Installation

Blog Article

Schedule Service Now

This post down below in relation to Tools You Need to Install a New Bathtub is immensely captivating. Try it and make your own final thoughts.


How to Install a Bathtub Yourself
Mounting a tub isn't precisely brain surgery, however it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably tough project. If the old tub is readily obtainable, the task can relocate immediately; if you need to open up a wall to eliminate the old tub and place the new tub, the task is a lot harder. In either instance, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also set in the new one. Make certain you have actually qualified yourself for the task as well as fit trying it. Rather than working with a specialist to take control of a halfway-completed task, it is far better to consider employing one before you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly help you set up a new tub in your bathroom if you have currently bought a new tub and also do not need to change the setup of your previous supply of water pipes.
Your tools and also product list must make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Planning for the Setup


    To start with, the sustaining structure supplied with the bathroom needs to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the bath tub.
    Fit the versatile tap ports to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washers.
    Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last setting.

    Removing Old Touches


    If you require to change old faucets with new ones as a part of your installation, then the first thing you must do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing taps can be rather bothersome because of the limited accessibility that is commonly the situation.
    Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will come from the pipes. When the supply pipes have actually been gotten rid of, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
    Before moving on to fit the new faucets, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.

    Installing the Tub


    Making use of both wood boards under its feet, position the bath tub in the required setting. The wood boards are helpful in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
    The next objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level reviews degree.
    To install faucets, fit the bottom of the outermost adaptable tap adapter to the suitable supply pipe by making a compression sign up with; after that do the same for the other faucet.
    Turn on the water as well as check all joints and new pipework for leakages and also tighten them if required. Fill the bathtub and additionally check the overflow electrical outlet and also the typical outlet for leakages.
    Lastly, repair the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the bathtub should wait up until the tub has actually been used at the very least once as this will resolve it right into its final setting.

    Fitting New Touches


    If the tails of the new taps are plastic, then you will certainly need a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the existing supply pipes.
    If you need to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next off, position the faucet in the installing opening in the bath/basin ensuring that the washers remain in area in between the tap and also the sink. Safeguard the faucet in position with the maker given backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous kind should be attached to the faucet finishes initially, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Tub


    In the location where the bathroom meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a rigid seal, creating the water to penetrate the wall in between the bathroom and the tiling, leading to complications with moisture and also feasible leakages to the ceiling below.
    You can choose from a variety of coloured sealants to blend in your components and installations. They are offered in tubes as well as cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Remember to always load the bathtub with water prior to sealing, to allow for the motion experienced when the tub remains in use. The sealant can split fairly very early if you do not think about this activity before securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof sticky and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    I am just very interested in How to Install a Bathtub Yourself and I hope you appreciated the entire page. You should take the time to distribute this article if you enjoyed reading it. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .


    Request An Appointment

    Report this page